Related topics

Internet working but programs can't find network connection
I am also using 2 network cards, one for the Internet connection, one for the LAN. However, the following case appeared. 1) When I setup the network again with I can even activate the Internet gateway connection to connect from my client. However, after connection, when I go to my web browser to surf/ browse,

Help - Computer Locks Up at End of Bootup
For whatever reason, it seems that the TCPIP implementation in XP is routing local traffic through the Internet, which slows down LAN traffic to a crawl. I have 3 boxes: 1 XP Pro and 2 Win98. I use a network Hub (Intel Office Connect) and a Hardware Firewall (SonicWall SOHO/10) with cable modem access (Motorola

Linux not ready for average user (was: Redhat 5.1 Internet ...
Everything's ok, it even detected that I have a network card that isn't connected, which is true, BUT it hasn't detected my modem. I'm searching for something like 'Connect to the Internet', but find nothing. It seems they assume I would automaticaly connect at the start, but hey, who cares us Eastern-Europeans

Newsgroups for Dummies FAQ v0.05, for the PPP Project.
Charges begin when you press "SEND" or "CONNECT" button, or upon connection to system. On incoming calls, charges may begin prior to device ringing and before you Express Network data-capable tri-mode equipment with updated software is required. Customers must dial *228 to activate on or migrate to the Express

MacOS X networking setup
My internet connection works well ... appart that I can't connect to the Microsoft.com site!!! The support.microsoft.com site works fine but not the normal www.microsoft.com one. I can't neither connect with messenger (key ports problem...). Neither of course activate windows... My hosts file is clean (only one

A los Maestros del _Emule
You need to activate routing in that PC. You need to tell the routing that anything with 192.168.1.x goes out over the LAN card and anything else (usually This means if the DOWNSTAIRS PC tries to connect to something not on its network (192.168.1.x) then the DOWNSTAIRS PC is to send the request to the gateway

Getting NDO on the internet blues
I could connect the PDA to the FIDO network with a GSM adaptor, or Clearnet's iDen network, or Telus's or Bell's CDMA network. When I'm at the office my PDA gains access to the network and the internet through it's hotsync cradle. That $200-500 investment in the PDA and the $200-$500 investment in a Compact Flash

RH: Bad news for Singtel and LHY
Right-click the network connection to the LAN, and click on the advanced tab. ICF is enabled by the check box in the upper panel--You must either uncheck this, or click on Settings, and enable remote desktop inbound traffic to pass through the firewall. Note: It may be a good practice to activate the firewall on

RH9 Ethernet/Internet Not Working
Note: I'm *only* going to connect the two computers together. I don't need any internet connection, neither do I have a router/hub to do this. Exactly. You should activate Personal File Sharing AND Windows Sharing (= smb = SAMBA). OK. All service are now turned off except "Personal file sharing" and "Windows

My Debian box can't connect Internet
Setting up a TCP/IP network 1. Click start, settings, control panel. 2. Click Internet- select connection. 3. Select "connect to the Internet using a LOCAL area network, why? If you connect to the Internet with your modem, initiating the TCP/IP in F4 will activate your dial up adapter, thus causing F4 to "hang.

IE will not connect to internet after installing sp2
ADSL modem - When I open the TCP/IP control panel, the only choice I'm offered for "Connect via" is "Appletalk (MacIP)". My question: Do I need a system extension in order to activate the PCI slot? If so, how do I obtain it? You do need a driver for that card and it may have to be patched as well.

News, 27-28/6/00 (3)
This software will bridge from the first network card to the second. Connect the second NIC to the Switch and all the other computers to the switch. I'm trying to install two PCI NIC in one Windows 98 system in order to share internet cablemodem connection, using a 5 port 10/100 switch.

WinXP home vs Pro
I have a cable connection, and I used the internet connection tool and added my netword card (I think), and set it to eth0. I got the other information about the network card from Windows (IRQ, memory, IO...), and when I click "activate" it says it cannot activate the device. I know enough to get this far,

Why can't activate?
Will the telephone connection mess up my internet? Where is the timer and programme planner? My signal strength seems a bit low - is this a problem? .... Go into the hidden installer's menu and activate the RF2 power output. You must connect the TV Link to the RF2 socket. Never be tempted to activate the RF2 power

how to use or activate samba
Like other Microsoft Network-based devices being produced by PC makers and consumer electronics companies, Emachines' unit will use Microsoft's Windows CE operating system to connect directly to the Internet through Microsoft's MSN service. The device will hit shelves and Web sites this fall.

Can't connect to the internet!
I can connect to the Internet and use Outlook Express from the XP Pro machine using the dial up connection on the 98 PC so I assume that internet connection sharing has been Is there a way to activate a gateway icon on the remote XP Pro machine on the wireless network so that I can terminate the connection?

Duplicate name on Network
Please make sure your TCP/IP are configured properly for both network cards. IPX and netbeui cannot be used for internet - only TCP/IP -- Jon Hildrum DTS MVP This software will bridge from the first network card to the second. Connect the second NIC to the Switch and all the other computers to the switch.

PC buyers face product deactivation
Hi EVERYONE : version : RED HAT 5.1 LINUX I have a home network using Linux server to connect internet by ppp and network card connect my local PC. I check the Linux server by using PPP to internet is working. It can ping and http to the outside work. I try to activate the network card eth0 and add the address to

Home Network - Computers Can't See Each Other
pml m1343(a)abc...@example.org microsoft public virtualpc Just activate the internet connection sharing on the network connection/network adapter on the host that is connected to the internet. You may have to set DNS server on the guest manually and set the default gateway to 192.168.0.1 . hello,pml thank you

Internet Access from LAN
Install, activate, or do what you need to do to configure the wireless NICs of the computers you want to connect to the router. (You do have wireless network cards, right?) 5. Disable bridging. Bridging is used when you have a computer with two or more network cards. One NIC is connected to the Internet.